FAQ
Wybierz
Master-Slave to teraz Main-Follow - funkcja jest taka sama!
Master-Slave to teraz Main-Follow - funkcja jest taka sama! Jeśli urządzenie podłączone do Main-Gniazdo jest włączone, wszystkie urządzenia w Follow-gniazda są automatycznie włączone. Jeśli przez Main-gniazdo nie przepływa już prąd, gniazda Follow są automatycznie wyłączane.
Dlaczego funkcja master-slave nie działa prawidłowo z laptopami?
Funkcja Main-Follow opiera się na pomiarze poboru prądu w gnieździe Main.
Jeśli pomiar jest powyżej ustawionego progu, gniazda następcze są automatycznie włączane.
Jeśli pomiar jest poniżej ustawionego progu, gniazda Follow są automatycznie wyłączane.
W przypadku urządzeń zasilanych bateryjnie, takich jak laptopy, zużycie prądu nie musi jednak odpowiadać stanowi pracy w stanie włączonym lub wyłączonym.
Pobór prądu może być również wyższy od wartości progowej (naładuj akumulator) przy wyłączonym laptopie lub niższy od wartości progowej przy włączonym laptopie.
lub poniżej wartości progowej, gdy laptop jest włączony (bateria pełna i laptop pracujący na małej mocy).
Stosowanie urządzeń zasilanych bateryjnie jako urządzeń nadrzędnych jest zatem generalnie niewłaściwe.
Which are the advantages of the digital Main-Follow function?
With these models the switching threshold can be set up automatically via the push of a button. If you don’t require the Main-Follow function at the moment, you can activate the permanent mode for the follow sockets if desired. The extension lead will then ignore the Main-Follow function. The stored switching threshold, or rather the permanent mode, will also remain if the Main-Follow extension lead is temporarily turned off by the main switch.
Dlaczego moja automatyczna listwa zasilająca nie wyłącza już gniazdek Follow?
Niektórzy użytkownicy uważają, że gniazda Follow nie są wyłączane, mimo że urządzenie główne jest wyłączone. Może to być spowodowane bardzo wysokimi prądami rozruchowymi podłączonych urządzeń Follow, które znacznie przekraczają maksymalną obciążalność przekaźnika i tym samym spawają styki przełączające.
W wielu przypadkach styki przełączające mogą zostać ponownie odłączone od siebie poprzez wibracje (stukanie) i w ten sposób tymczasowo przywrócone do działania. Jednak bez zmiany konfiguracji jednostek Follow, problem zazwyczaj szybko powraca.
Tło:
Nasze automatyczne listwy gniazdowe, jako całość oraz zastosowane w nich przekaźniki, przystosowane są do ciągłego obciążenia prądami o wartości 16A. Urządzenia końcowe z ochronną wtyczką stykową nie mogą pobierać większego prądu. Jednak niektóre urządzenia końcowe przekraczają ten limit wielokrotnie już w momencie włączenia. Pobór prądu może wzrosnąć do 50A lub więcej przez ułamek sekundy. Te wysokie prądy mogą spowodować zgrzanie styków przełączających w przekaźniku - przekaźnik nie będzie się wtedy wyłączał.
Z doświadczenia wynika, że problem ten występuje częściej w terminalach z zasilaczami impulsowymi. Można je dziś zainstalować prawie wszędzie, np. w komputerze, monitorze, drukarce, zewnętrznych dyskach twardych, aktywnych głośnikach itp. To, które produkty rzeczywiście powodują takie problemy, zależy również od tego, czy producenci urządzeń końcowych podjęli odpowiednie środki zapobiegające nadmiernym prądom rozruchowym, czy też nie. Niestety, nie można tego odczytać z żadnej karty katalogowej ani tabliczki znamionowej. Zoptymalizowaliśmy pod tym względem nasze automatyczne listwy gniazdowe poprzez zastosowanie specjalnych przekaźników dla obciążeń impulsowych do 80A. Dzięki temu problem ten występuje znacznie rzadziej.
What can I use an automatic extension lead with Main-Follow function for?
With the on/off switch of a single device plugged into the main socket, all other devices in the follow sockets can be switched on and off automatically. You can use a computer as the main device, for example, which includes monitors, printers, modems, etc. as follow devices in the automatic control. Of course, combinations of TV, radio, receiver, etc. can also be controlled.
How do I set the switching threshold on an automatic extension lead with setting controller?
1. Plug your main unit into the red main socket and switch it on.
2. Turn the switching threshold control slowly and carefully until you find a position where the follow sockets are switched on and off. Make a note of this control position 1 (the follow sockets always remain on for consumers with high current consumption).
3. Now switch off your main unit again, but leave it plugged in.
4. Turn the switching threshold control slowly and carefully until you find a position at which the follow sockets are switched on and off. Make a note of this control position 2 (for consumers without or with low standby current consumption, the follow sockets always remain off).
5. Now place the setting control centrally between control position 1 and control position 2. (In cases where you could not determine control positions 1 or 2, please place the setting control centrally between the control stops).
How do I set the switching threshold on an automatic extension with digital Main-Follow function?
These devices have an automatic switching threshold setting that is started by pressing a button.
1. Switch on the automatic extension lead at the main switch.
2. Plug the main unit into the red main socket.
3. Put the main unit in standby mode or switched off mode, if this is not already the case.
4. Press and hold the "Learn" button on the automatic extension lead for approx. 3 seconds until the "Follow on" lamp starts to flash.
5. The "Follow on" lamp now flashes for a short time. During this time, the standby power consumption of the main unit is automatically determined and the switching threshold is saved.
6. When the "Follow on" lamp stops flashing, the setting process is finished. The automatic switching function can now be used.
Permanent mode with an automatic extension lead with digital Main-Follow function
Activation of the permanent mode:
- Proceed in the same way as for the automatic switching threshold setting.
- While the "Follow on" lamp is flashing (point 5), press the "Learn" button again for approx. 3 sec. The automatic switching threshold setting is terminated and the permanent mode for the follow sockets is activated.
Deactivating the permanent mode:
- Simply perform an automatic switching threshold setting again.